A flooring guide and connection service. This site is not a flooring contractor and installs nothing.

Winton Flooring The Sample Board: every floor, sectioned and labelled

The ledger · Cost guide + estimator

What flooring costs, printed as a ledger, with an estimator that uses nothing else.

These are typical planning ranges for the US market, in USD, checked November 2026, with assumptions printed beside every rate. They are not quotes and not any one business's price list. The estimator below computes from exactly this table: pick a floor, enter your area, tick the add-ons your job honestly needs, and the arithmetic it prints is arithmetic you can re-check by hand against the ledger.

The printed ledger

WorkUnitPlanning rangeAssumptions printed with the rate
Solid hardwood, installedper sq ft$9.00 – $15.00Mid-grade domestic species, nail-down, standard rooms
Engineered hardwood, installedper sq ft$8.00 – $14.004 mm-class veneer, glue / staple / float
Luxury vinyl plank / tile, installedper sq ft$5.00 – $10.00Rigid core, 20 mil wear layer class
Laminate, installedper sq ft$4.00 – $8.00AC3–AC4, underlayment included
Ceramic / porcelain tile, installedper sq ft$9.00 – $17.00Standard format, membrane or backer included
Carpet with pad, installedper sq ft$3.50 – $7.50Mid-grade nylon / triexta, 8 lb rebond pad
Refinishing existing hardwoodper sq ft$3.00 – $6.00Full sand, 3 coats; recoat-only runs lower
Tear-out & disposal of existing floorper sq ft$1.50 – $3.00Add-on; tile tear-out prices at the top and above
Subfloor prep / levellingper sq ft$1.00 – $2.50Add-on; patch / self-leveller to tolerance
Moisture barrier / upgraded underlaymentper sq ft$0.50 – $1.25Add-on; over concrete or for acoustics
Waste & cutting allowancemultiplierx 1.10Applied to the subtotal; diagonal / patterned layouts need 15%

Not in the ledger, deliberately: stairs (priced per tread), pattern-match carpet waste beyond the standard allowance, structural subfloor repair, asbestos testing and abatement in older sheet goods and mastics, and furniture moving. Each is real scope; a single blended rate for them would be a fiction.

The estimator

1 — Floor
2 — Add-ons your job needs

Refinishing note: tear-out and underlayment do not apply to a refinish; the estimator ignores them if ticked with refinishing selected, and says so.

Planning range

With JavaScript off, the estimator cannot compute, so plan from the printed ledger above: multiply your square footage by the floor's rate band, add any add-on bands per square foot, then multiply the subtotal by 1.10 for the waste and cutting allowance. Worked example: 500 sq ft of LVP at $5.00–$10.00 is $2,500–$5,000; with tear-out at $1.50–$3.00 the subtotal is $3,250–$6,500; with the 10% allowance the planning range is $3,575–$7,150.

Worked example, by hand

800 sq ft of solid hardwood, no add-ons. Ledger: $9.00–$15.00 per sq ft. 800 × $9.00 = $7,200; 800 × $15.00 = $12,000. Subtotal $7,200–$12,000. Waste and cutting allowance ×1.10: $7,920–$13,200. Planning range: about $7,920–$13,200. Run the same entries in the estimator; it prints the same lines in the same order.

What moves a real quote outside the range

  • Prep found at tear-out: rotten OSB, a slab at 92% RH, a floor an inch out of flat. The range assumes the tolerances on the subfloor page; reality sometimes bills more.
  • Pattern and layout: herringbone, borders, and diagonal runs add labour and push waste toward 15%.
  • Stairs, transitions, and trim: priced per piece, and they add up in split-levels and open plans.
  • Region and access: high-cost metros, upper floors without lifts, and occupied homes all price time, legitimately.

Turn a planning range into a real quote — request a connection